Tria Laser Hair Removal - How to Treat

Unlock the Laser

The Tria Laser 4X will lock when it’s not in use. To unlock the Tria Laser 4X, use the Skin Sensor on the bottom of the unit, which helps confirm that the Tria laser is safe for your skin tone.

To unlock:

  1. Unplug the Tria Laser 4X from the battery charger and press the power button to turn it on. The display will show the lock and skin sensor icons
  2. Hold the skin sensor (Red light at the base of the Tria Laser 4X) against the skin in the area you wish to treat.  The skin sensor will automatically sense and check your skin. If the Tria Laser 4X is safe for your skin tone, the Tria Laser 4X will emit a series of beeps and unlock.
  3. If the lock icon is still visible and you do not hear a series of beeps, then it may not be safe for you to use the Tria Laser 4X. Or, you may be using the skin sensor incorrectly and need to try again. To try again, lift the skin sensor from your skin and then follow steps 1 & 2 again. If you cannot unlock the Tria Laser 4X, please contact Customer Services for assistance.
Unlocking the Tria Laser 4X

Setting the Treatment Level

The Tria Laser 4X has different energy levels. In a clinical study, higher levels were found to be 2-3 times more efficient.
So for best results, we recommend you use the highest setting that you can tolerate.

When the Tria Laser 4x is on and unlocked, press the power button to select your desired level. Each time you press the power button, the level will increase. Once the Tria Laser 4x is at the maximum level, pressing the power button again will return it to the lowest level.

Setting the Treatment Level

How to Treat

Cleanse, shave and thoroughly towel-dry skin.

Apply a thin layer of Smoothstart Calming Gel to help keep theskin calm and comfortable.

Turn on the Laser, unlock it and set the treatment level (see above)

Touch and hold the treatment window to the skin until you hear two beeps.

  • If you do not hear beeps, make sure that the treatment window is flat against your skin.
  • If you hear a buzzing tone instead of the second beep, you lifted the device from the skin before the pulse was over.
  • Do not move the treatment window between the first and second beep because this will disrupt the laser pulse and reduce its effectiveness.
How to Treat Using the Tria Laser 4X

Lift the Laser and place it back on the skin so that it overlaps the previous spot.

  • Each time you reposition the treatment window, move it about half the distance of the window (about ¼ inch or 5cm). This creates and overlapping pattern in the treatment area, which ensures you cover all the hair follicles.
    This works out to about 25 laser pulses per square inch or 40 pulses per 10 square cm. 
How to Treat Using the Tria Laser 4X

DO NOT treat repeatedly in the same spot. Always move the treatment window to a new area after each laser pulse. Failure to do so may result in discomfort or skin heating, which could cause skin injury. 

Keep going until you have completely covered the area you want to treat.
Use the tria Laser 4X Pulse Counter to help get the best results. See the table as a guide to how many pulses you may need to cover each area per treatment. These pulse counts and times are approximations – your actual treatment area and number of pulses may vary. Always follow the treatment instructions and warnings provided in your handbook.

Note: When treating larger areas like legs and back, you may need more than 600 pulses to cover the area using an overlapping pattern. If so please recharge the Tria Laser 4X and continue treating until you’ve covered the desired treatment area.

Tria Laser 4X Pulse Counter Table Tria Laser 4X Pulse Counter Table

Turn off the Laser 4X by holding down the power button.

Repeat treatment every 2 weeks for up to 3 months or until you reach the desired results.

Note: The cooling fan may go on and off during your treatment. This is normal and nothing to worry about.


WHAT TO EXPECT

While Using the Tria Laser

BEFORE TREATMENTS

What to do Before Starting Treatment